Osburn 950 Series Wood Burning Stove
Would you like to add a dose of warmth and cozyness to your home? Bring comfort and functionality to your daily life with the Osburn 950, a small wood stove that will quickly become your cold-season essential.
Equipped with high density bricks, a stainless steel heat shield added to the C-Cast firestop, a top heat deflector to redirect heat in front of the stove as well as side panels that reduce clearances, the Osburn 950 offers quality and performance. Enjoy your winter evenings more than ever before!
Appliance Performance
- Fuel type: Dry cordwood (16" recommended)
- Recommended heating area-ft²: 250 - 1,200
- Overall firebox volume-ft³: 1.7
- EPA loading volume-ft³: 1.55
- Maximum burn time: 5 h
- Maximum heat output-dry cordwood: 45,000 BTU/h (13.19 kW)
- Overall heat output rate: 12,124 BTU/h (3.55 kW) to 26,700 BTU/h (7.83 kW)
- Average overall efficiency (dry cordwood): 74 % (HHV) (4) 79 % (LHV) (5)
- Optimum overall efficiency: 80 %
- Optimum heat transfer efficiency: 79 %
- Average particulate emissions rate: 1.8 g/h
- Average CO: 74 g/h
(1) Values are as measured per test method, except for the recommended heating area, firebox volume, maximum burn time, and maximum heat output.
(*) Recommended heating area and maximum burn time may vary subject to location in the home, chimney draft, heat loss factors, climate, fuel type, and other variables. The recommended heated area for a given appliance is defined by the manufacturer as its capacity to maintain a minimum acceptable temperature in the designated area in case of a power failure.
(2) The maximum heat output (dry cordwood) is based on a loading density varying between 15 lb/ft³ and 20 lb/ft³ and reloading intervals ranging from 60 to 120 minutes. Other performances are based on a fuel load prescribed by the standard without any reloading between start and finish. The specified loading density varies between 7 lb/ft³ and 12 lb/ft³. The moisture content is between 19% and 25%.
(3) As measured per CSA B415.1-10 stack loss method.
(4) Higher Heating Value of the fuel.
(5) Lower Heating Value of the fuel.
(6) Performances based on a fuel load prescribed by the standard at 7 lb/ft³ and with a moisture content between 19% and 25%.
(7) Optimum overall efficiency at a specific burn rate (LHV).
(8) The optimum heat transfer efficiency is for the low burn rate (using HHV) and represents the appliance’s ability to convert the energy contained in the wood logs into energy transferred to the room in the form of heat and does not take into account the chemical losses during combustion.
(9) This appliance is officially tested and certified by an independent agency.
(10) Carbon monoxide.
General Features
- Combustion technology: Non-catalytic
- High-efficiency certified appliance: Yes, EPA 2020 approved
- Maximum log length: 17"
- Log positioning: Loading over depth
- Chimney diameter: 6"
- Flue outlet diameter: 6"
- Type of chimney: CAN/ULC S629, UL 103 HT (2100 °F)
- Minimum chimney height (feet): 12'
- Baffle type: C-Cast or equivalent
- Approved for an alcove installation: Yes
- Approved for a mobile home installation: Yes, with fresh air intake
- Shipping Weight: 317 lb (144 kg)
- Door type: Single, glass with cast iron frame
- Glass type: Ceramic glass
- Glass surface – dimensions (Width X Height): 10 1/4" x 8 7/8"
- Glass air-wash system: Yes
- Overall dimension (Height): 28 7/8''
- Overall dimension (Width): 20 1/4''
- Overall dimension (Depth): 27 7/8''
- Door opening – dimension (Height): 7 5/8"
- Door opening - dimension (Width): 12"
- Firebox – dimension (Height): 11 3/4"
- Firebox – dimension (Width): 14 1/4"
- Firebox – dimension (Depth): 19 1/8"
- Firebox lined with refractory bricks for better heat distribution: Yes
- Stainless-steel secondary-air system improving gas combustion: Yes
- Steel thickness – body: 3/16"
- Steel thickness – top: 5/16"
- USA standard (emissions): EPA
- Canadian Standard (emissions): CSA B415.1-10
- USA standard (safety): UL 1482, UL 737
- Canadian standard (safety): ULC S627
- Tested and listed as per applicable standards: By an accredited laboratory (CAN/USA)
- Warranty: Limited lifetime
Options
|
5"Ø Fresh Air Intake Kit for Wood Stove on Legs The kit contains one assembled fresh air intake box, two clamps, one white exterior wall termination, black metallic paint, one black pre-glued gasket, one flat rod, one ground rod, and screws. The number of screws may vary depending on the assembly. |
 |
|
5" X 4' Insulated Flex Pipe for Fresh Air Intake Kit
|
 |
|
5'' Fresh Air Intake Register with Airtight Damper
|
 |
|
Blower with Thermodisc Osburn Blower with Thermodisc. |
 |
|
Rigid Firescreen Removable screen preventing flying sparks. Enhances the crackle and the incomparable atmosphere of a good fire. |
 |
Manuals
Would you like to add a dose of warmth and cozyness to your home? Bring comfort and functionality to your daily life with the Osburn 950, a small wood stove that will quickly become your cold-season essential.
Equipped with high density bricks, a stainless steel heat shield added to the C-Cast firestop, a top heat deflector to redirect heat in front of the stove as well as side panels that reduce clearances, the Osburn 950 offers quality and performance. Enjoy your winter evenings more than ever before!
Appliance Performance
- Fuel type: Dry cordwood (16" recommended)
- Recommended heating area-ft²: 250 - 1,200
- Overall firebox volume-ft³: 1.7
- EPA loading volume-ft³: 1.55
- Maximum burn time: 5 h
- Maximum heat output-dry cordwood: 45,000 BTU/h (13.19 kW)
- Overall heat output rate: 12,124 BTU/h (3.55 kW) to 26,700 BTU/h (7.83 kW)
- Average overall efficiency (dry cordwood): 74 % (HHV) (4) 79 % (LHV) (5)
- Optimum overall efficiency: 80 %
- Optimum heat transfer efficiency: 79 %
- Average particulate emissions rate: 1.8 g/h
- Average CO: 74 g/h
(1) Values are as measured per test method, except for the recommended heating area, firebox volume, maximum burn time, and maximum heat output.
(*) Recommended heating area and maximum burn time may vary subject to location in the home, chimney draft, heat loss factors, climate, fuel type, and other variables. The recommended heated area for a given appliance is defined by the manufacturer as its capacity to maintain a minimum acceptable temperature in the designated area in case of a power failure.
(2) The maximum heat output (dry cordwood) is based on a loading density varying between 15 lb/ft³ and 20 lb/ft³ and reloading intervals ranging from 60 to 120 minutes. Other performances are based on a fuel load prescribed by the standard without any reloading between start and finish. The specified loading density varies between 7 lb/ft³ and 12 lb/ft³. The moisture content is between 19% and 25%.
(3) As measured per CSA B415.1-10 stack loss method.
(4) Higher Heating Value of the fuel.
(5) Lower Heating Value of the fuel.
(6) Performances based on a fuel load prescribed by the standard at 7 lb/ft³ and with a moisture content between 19% and 25%.
(7) Optimum overall efficiency at a specific burn rate (LHV).
(8) The optimum heat transfer efficiency is for the low burn rate (using HHV) and represents the appliance’s ability to convert the energy contained in the wood logs into energy transferred to the room in the form of heat and does not take into account the chemical losses during combustion.
(9) This appliance is officially tested and certified by an independent agency.
(10) Carbon monoxide.
General Features
- Combustion technology: Non-catalytic
- High-efficiency certified appliance: Yes, EPA 2020 approved
- Maximum log length: 17"
- Log positioning: Loading over depth
- Chimney diameter: 6"
- Flue outlet diameter: 6"
- Type of chimney: CAN/ULC S629, UL 103 HT (2100 °F)
- Minimum chimney height (feet): 12'
- Baffle type: C-Cast or equivalent
- Approved for an alcove installation: Yes
- Approved for a mobile home installation: Yes, with fresh air intake
- Shipping Weight: 317 lb (144 kg)
- Door type: Single, glass with cast iron frame
- Glass type: Ceramic glass
- Glass surface – dimensions (Width X Height): 10 1/4" x 8 7/8"
- Glass air-wash system: Yes
- Overall dimension (Height): 28 7/8''
- Overall dimension (Width): 20 1/4''
- Overall dimension (Depth): 27 7/8''
- Door opening – dimension (Height): 7 5/8"
- Door opening - dimension (Width): 12"
- Firebox – dimension (Height): 11 3/4"
- Firebox – dimension (Width): 14 1/4"
- Firebox – dimension (Depth): 19 1/8"
- Firebox lined with refractory bricks for better heat distribution: Yes
- Stainless-steel secondary-air system improving gas combustion: Yes
- Steel thickness – body: 3/16"
- Steel thickness – top: 5/16"
- USA standard (emissions): EPA
- Canadian Standard (emissions): CSA B415.1-10
- USA standard (safety): UL 1482, UL 737
- Canadian standard (safety): ULC S627
- Tested and listed as per applicable standards: By an accredited laboratory (CAN/USA)
- Warranty: Limited lifetime
Options
|
5"Ø Fresh Air Intake Kit for Wood Stove on Legs The kit contains one assembled fresh air intake box, two clamps, one white exterior wall termination, black metallic paint, one black pre-glued gasket, one flat rod, one ground rod, and screws. The number of screws may vary depending on the assembly. |
|
|
5" X 4' Insulated Flex Pipe for Fresh Air Intake Kit
|
|
|
5'' Fresh Air Intake Register with Airtight Damper
|
|
|
Blower with Thermodisc Osburn Blower with Thermodisc. |
|
|
Rigid Firescreen Removable screen preventing flying sparks. Enhances the crackle and the incomparable atmosphere of a good fire. |
|
Manuals
Related Products
Osburn 2000 Wood Burning Stove With Blower
$2,299.00
$2,829.99
SAVE
19%
Osburn Matrix Wood Burning Stove with Blower
$3,199.00
$3,939.99
SAVE
19%
Osburn Inspire 2000 Wood Stove
$2,749.00
$3,379.99
SAVE
19%
Osburn 2500 Pellet Stove
$3,999.00
$4,919.99
SAVE
19%
